modele

Ojrzan/sup-cup-phone-holder-2.scad

@@ -0,0 +1,164 @@
+
+// The following should be editable within reason to adjust for container and phone size
+
+$fn=50; // number of facets to the cylinders - basically level of detail
+
+drink_rad = 46;     // radius of drink container - allow some wiggle room
+phone_width = 80/2;   // width of phone - allow some wiggle room
+phone_depth = 8;    // depth of phone - allow some wiggle room
+
+
+// not intended to be changed
+holder_rad = drink_rad + 5;
+base_rad = holder_rad + 5;
+
+
+module cup_holder_base_shape() {
+
+    // basic shape for cup holder
+    
+    union() {
+        
+        // lower base
+        cylinder(h=2,r=base_rad,center=true);
+        
+        // upper base
+        translate([0,0,2.99])
+        cylinder(r2=holder_rad,r1=base_rad,h=5,center=true);
+        
+        // holder
+        translate([0,0,48.99])
+        difference() {
+            cylinder(r=holder_rad,h=90,center=true);
+            // cut to hollow out cup
+            cylinder(r=drink_rad,h=91,center=true);
+        }
+        
+    }
+    
+}
+
+
+//cup_holder_base_shape();
+
+
+
+module cup_holder_finished() {
+    
+    // cut features from basic cup holder shape
+
+    difference() {
+        cup_holder_base_shape();
+        
+        // cut side slot for strap
+        translate([0,drink_rad,54])
+        rotate([0,10,10])
+        cube([5,20,95],center=true);
+        
+        // cut other side slot for strap
+        translate([0,-drink_rad,54])
+        rotate([0,-10,10])
+        cube([5,20,95],center=true);
+        
+        // cut bottom slot for strap
+        translate([0,0,6.5])
+        rotate([90,0,13])
+        cylinder(r=2.75,h=120,center=true);
+        
+        // cut drainage holes
+        translate([0,0,0])
+        cylinder(r=6,h=40,center=true);        
+        
+        translate([20,5,0])
+        cylinder(r=4,h=40,center=true);
+        
+        translate([-20,-5,0])
+        cylinder(r=4,h=40,center=true);
+    }
+}
+
+//cup_holder_finished();
+
+
+
+
+module cylinder_cube(cr1=4,cr2=4,ch=5,cx=50,cy=10) {
+    
+    // makes a cube rounded on 4 sides
+    // can be narrower at top (used this for the beveled section)
+    // cr1 - bottom corner radius
+    // cr2 - top corner radius
+    // ch - height
+    // cx - length
+    // cy - width
+    
+    hull() {
+        
+        translate([cx-cr1,cy-cr1,0])
+        cylinder(r1=cr1,r2=cr2,h=ch,center=true);
+        
+        translate([cx-cr1,-cy+cr1,0])
+        cylinder(r1=cr1,r2=cr2,h=ch,center=true);
+        
+        translate([-cx+cr1,cy-cr1,0])
+        cylinder(r1=cr1,r2=cr2,h=ch,center=true);
+        
+        translate([-cx+cr1,-cy+cr1,0])
+        cylinder(r1=cr1,r2=cr2,h=ch,center=true);
+    }
+    
+}
+
+//cylinder_cube();
+
+
+
+
+module phone_holder() {
+    difference() {
+        union() {
+            
+            //lower base
+            cylinder_cube(cr1=6,cr2=6,ch=2,cx=phone_width+10,cy=phone_depth+10);  
+            
+            // upper base
+            translate([0,0,2.99]) 
+            cylinder_cube(cr1=6,cr2=2,ch=5,cx=phone_width+9,cy=phone_depth+9); 
+            
+            //holder
+            translate([0,0,34.99])
+            difference() {
+                cylinder_cube(cr1=2,cr2=2,ch=61,cx=phone_width+5,cy=phone_depth+5); 
+                translate([1,0,.1])
+                cylinder_cube(cr1=3,cr2=3,ch=62,cx=phone_width,cy=phone_depth);
+            }
+            
+        }
+        
+        // cut drainage hole
+        translate([0,0,.1])
+        cylinder_cube(cr1=2,cr2=2,ch=30,cx=20,cy=3);
+        
+    }
+}
+
+//phone_holder();
+
+
+
+
+module combo_holder() {
+    
+    // merge the two pieces
+    
+    union(){
+        
+        rotate([0,0,-12])
+        cup_holder_finished();
+        translate([holder_rad + phone_width,0,0])
+        phone_holder();
+    }
+    
+}
+
+combo_holder();

Oliwka/doniczka_ściana.scad

@@ -6,9 +6,27 @@ doniczka_d = 105;
 wall_w = doniczka_d+2*t;
 dystans=20;
 
+katownik_h = 25 + 1;
+katownik_w = 17 + 1;
+katownik_t = 2;
+
 union() {
   // wall mount
+  difference() {
     translate([-wall_t, -wall_w/2]) cube([wall_t, wall_w, wall_h]);
+    translate([-wall_t-0.1, -katownik_w/2 - wall_w/3])
+      union() {
+        cube([katownik_t, katownik_w, katownik_h]);
+        rotate([0,45,0]) translate([-1.5,0,0])
+          cube([katownik_w, katownik_w, katownik_t+2]);
+      }
+    translate([-wall_t-0.1, -katownik_w/2 + wall_w/3])
+      union() {
+        cube([katownik_t, katownik_w, katownik_h]);
+        rotate([0,45,0]) translate([-1.5,0,0]) 
+          cube([katownik_w, katownik_w, katownik_t+2]);
+      }
+  }
   difference() {
     union() {
       translate([0,-wall_w/2,0]) cube([wall_w/2+dystans, wall_w, t]);

Oliwka/szklanka.scad

@@ -1,5 +1,5 @@
-szerokosc_szklanki = 45;
-grubosc_szkla = 4;
+szerokosc_szklanki = 63;
+grubosc_szkla = 2.5;
 
 wysokosc_uchwytu = 10;
 dlugosc_uchwytu = 15;